4X Classic Mb Racing Wheels R16X8J" Alloy and 35 similar items

4X SET CLASSIC MERCEDES-BENZ RACING WHEELS R16XJ8" ALLOY RONAL/PENTA TYPE | DEALER THIS LISTING: 4 RIMS, R16 X J8 (8 INCH WIDE) INCH WIDE | READY TO USE 4X RIMS SET ONLY: NO VALVES, NO DECALS, NO TIRES, NO CENTER CAPS. EXTRAS GRAY STAR CENTER CAPS $100.00 X4 RIM VALVE $40.00 MB TYPE X 4 AMG DECALS $40.00 X 12 UNITS RACING STUDS NUTS $150.00 X20 RACING HOOSIER TIRES H20 $1,450.00 SET OF 4 AVAILABLE: 225/45/R16 AND/OR 225/50/R16 235/45/R16 AND/OR 235/45/R16 WE USE ONLY HOOSIER RACING TIRE UNIQUE CLASSIC MB: W107, W108, W109, W123, W107, W113 OTHER MB CLASSICS CHASSIS UPGRADE FROM R14-R15-R16 WHEELS. YEARS 1967-2000 (UP TO 2019, ON SOME MODELS) MERCEDES-BENZ CLASSIC RACING RIMS R 16 X J8" X 4 UNITS Hoosier Racing Tire Sports Car DOT Radial R7 tires are Racetrack Autocross Only tires developed for drivers who compete in road racing where responsiveness and high levels of grip in hot, dry conditions are desirable. Radial R7 tires are designed to reward drivers with fast, consistent lap times and extended wear due to their traction and handling. NOTE: Radial A7 tires are also used for road racing on lightweight cars or when competing in cool ambient temperatures where Hoosier Sports Car DOT Radial R7 tires cannot be brought up to favorable operating temperatures. WARNING: DOT labeled Hoosier Racing Tires meet Department of Transportation requirements for marking and performance only and are NOT INTENDED FOR HIGHWAY USE. It is unsafe to operate any Hoosier Racing Tire, including DOT tires, on public roads. The prohibited use of Hoosier Racing Tires on public roadways may result in loss of traction, unexpected loss of vehicle control, or sudden loss of tire pressure, resulting in a vehicle crash and possible injury or death. And like all Racetrack Autocross Only tires, R7 Radials are not intended to be driven in near-freezing temperatures, through snow or on ice. It's also essential these tires be stored indoors at temperatures maintained above 32 degrees F. The tread compound of Sports Car DOT R7 Radials is molded into a slick tread design interrupted only by five-dash circumferentially oriented grooves alternating outboard and inboard. Beginning with a tread depth of 4/32", they will not require shaving for competition, however they will benefit from a minimal scuff-in prior to their first runs. The tire's internal structure features a symmetric construction that uses two lightweight steel belts reinforced by a spirally wrapped circumferential nylon cap ply under the tread on top of two nylon cord casing plies. It features a rim recess design on all sizes. Additionally, its symmetric tread design and internal construction allows the tire to be mounted on either side of the car (and later be remounted inside out to further extend its life). Because of the way tires are manufactured, taking measurements of unmounted tires does not provide an accurate comparison. Hoosier DOT-radials typically have very generous unmounted dimensions, so be sure to mount on appropriate-width wheels before making any judgment related to physical size. The section width, tread width and shoulder profile of the R7 may differ from those of its predecessor, affecting the clearance between the tire and suspension components and/or body panels. If the intended application is an aggressive fitment with close tolerances, it is recommended to test fit a mounted, inflated tire to check for potential contact between the tire and vehicle before driving on the tires. Related Information: Care and Feeding of the Hoosier A7/R7 (PDF) | Competition Tire Heat Cycling Service | Storing Track Competition DOT Tires in Cold Temperatures