4-Blade Hay Cutter Pulverizer with Belt and similar items

4-blade hay cutter pulverizer with belt conveyor This machine is suitable for crushing all kinds of grass, corn, wheat, peanuts, beans and straw. The processed feed is more convenient for storage. It is a necessary machine for farmers, small and medium-sized feed processing plants and farms; At the same time, the machine can also be used together with the feed granulator to facilitate the feed machine to shape the feed into granules. Note: 1. In addition to commissioning according to the commissioning method, before starting, the machine must be carefully checked to see if there are tools and objects hindering the startup and operation, and whether the upper casing is locked. 2. Before starting the machine, it is necessary to check whether there are sundries in the machine. Except for processing straw, nothing is allowed to be stacked on the feeding table. 3. Run for 2-5 minutes before operation, check whether the rotating speed meets the requirements of the machine, never allow overspeed, and check whether other parts are abnormal. If everything is normal, the feeding can be started, and the feeding cannot be excessive, so as to prevent damage to the supporting power unit and machine parts due to overload operation. 4. When the machine is operating, it is forbidden to stand at the grass outlet to prevent flying objects from hurting the body. 5. Operators are not allowed to wear gloves, sleeves must be fastened, and those with long hair must wear safety helmets. All personnel must leave the rotating plane of belt and rotating parts. Product parameter: Product analysis: Feature: Precautions for operation: In order to ensure the safety and normal operation of the person and the machine, a special person shall be assigned to be responsible for the storage and use of the machine. The machine shall not be operated without learning this procedure and operation technology and reading the familiar instructions. 1. In addition to commissioning according to the commissioning method, before starting, the machine must be carefully checked to see if there are tools and objects hindering the startup and operation, and whether the upper casing is locked. 2. Before starting the machine, it is necessary to check whether there are sundries in the machine. Except for processing straw, nothing is allowed to be stacked on the feeding table. 3. Check whether the electrical equipment is normal and safe. 4. Check whether the running direction of the main shaft conforms to the direction indicated by the arrow on the casing. If not, immediately adjust and close the power switch to ensure the correct operation of the machine. 5. Run for 2-5 minutes before operation, check whether the rotating speed meets the requirements of the machine, never allow overspeed, and check whether other parts are abnormal. If everything is normal, the feeding can be started, and the feeding cannot be excessive, so as to prevent damage to the supporting power unit and machine parts due to overload operation. 6. Feed crops evenly, not too much, so as not to block the feed inlet. The operator's hand shall not be close to the feeding belt during operation. 7. In case of blockage, stop the machine immediately. After the machine stops stably, open the upper cover, clean the blockage, and then restart. 8. Always pay attention to whether there is abnormal sound during the operation of the machine. Shut down and power off immediately in case of abnormality. 9. There shall be no mortar, sand, stone, iron wire, tool parts or other sundries in the crops to be processed to avoid damage to the machine or accidents. 10. At the end of each shift, the power supply must be cut off after all the crops on the feeding table are fed and no more materials are thrown out at the outlet. 12. When the machine is operating, it is forbidden to stand at the grass outlet to prevent flying objects from hurting the body. 13. Operators are not allowed to wear gloves, sleeves must be fastened, and those with long hair must wear safety helmets. All personnel must leave the rotating plane of belt and rotating parts. ? ? Details: product advantages: ? 1.This machine is equipped with 4 sets of thickened blades, which can easily cut materials. Double-sided blades extend the service life of the blades. 2.This machine is equipped with a widened and thickened feeding port, which is solid and firm. All kinds of grass can be fed easily. It is equipped with a conveyor belt, which can feed automatically, which is more convenient and fast. 3.Customers can choose the length of material cutting by themselves, and there are two gears for customers to choose. 4.The screw in the blue circle can be moved back and forth to adjust the tightness of the conveyor belt. 5.This machine is equipped with lock nuts to ensure the locking and sealing of the engine room and improve the safety. 6.This machine is equipped with air switch, which is safer and more secure. 7.The feed inlet can be installed separately, and can be removed and placed when not in use, saving space. 8.The blades of this machine can be replaced. 9.This machine is equipped with high horsepower and high-quality motor. 10.The conveying roller of this machine can fluctuate flexibly according to the amount of material, which is more humanized. Product display: Item Number: 1*4-blade hay cutter pulverizer with belt conveyor (239594) You can make order with no worry. Any concerns just feel free to let us know, we'll reply in 24 hours in normal condition. Handling Time: Shipping is usually made in 1-3 business days after payments cleared. Orders are processed from Monday-Friday; Not on the weekends public holidays. Warranty: 6 months' warranty for the machines, not for the consumables. We stand behind our products all the item, so even if your warranty period has expired, you can still seek for service or technical support from us with low cost.